Set Descending Direction

Items 1-20 of 22

Page

RasPiO InsPiRing - Programmable RGB LED shapes - Circle + driver

All the boards are based on 1cm LED spacing and 10cm side
Controllable by Virtually any Platform
Programmable RGB LED boards which can connect together to make whatever 2D or 3D shape you want.
Each shape has at least one set of inputs and outputs so they can be daisy-chained together.

AB Electronics Expander Pi

16 channel digital input / outputs
8 channel 12 bit resolution analogue input (ADC)
Real time Clock (RTC) with CR2032 battery holder.
2 channel 12 bit resolution digital to analogue output (DAC)

MonkMakes Speaker for micro:bit

Reverse polarity protection
Amplified output
LED power on indicator

AB Electronics Servo PWM Pi Zero

Output frequency is programmable from a typical 40Hz to 1000Hz
The PCA9685 contains 5 I2C address selection pins
16-channel, 12-bit PWM controller for the Raspberry Pi

Pi Supply PiCrust ProtoHAT

The holes are connected underneath with traces to mimic the solderless breadboards
We break out nearly every pin you could want to connect to the Raspberry Pi.
The Pi Crust ProtoHAT has a grid of prototyping soldering holes for attaching chips

Pi Supply Flick Large - Standalone 3D Tracking and Gesture Breakout

Orange/green dual colour LED on board
Level shifting chip to enable board to work with 3V3 or 5V0 power and logic
Gesture sensing up to 15cm
3D tracking
Compatible with Raspberry Pi, BeagleBone, Arduino, Genuino or any I2C enabled device

AB Electronics 1 Wire Pi Zero

Stackable with other Raspberry Pi accessory boards
1-Wire to I2C host interface with ESD protection diode
External 5V power input for 1-Wire interface
Buffered 5V I2C port
I2C address selection via solder jumpers

AB Electronics Serial Pi Plus

Control the Raspberry Pi over RS232 or connect to external serial accessories.
Stackable with other Raspberry Pi accessory boards.
RS232 Master Port.
Mounting holes for use with the AB Electronics UK mounting kits (sold separately)

Pi Supply Ryanteck RTk.GPIO (PC GPIO Interface)

Compatible with most Raspberry Pi add-ons that use GPIO, this device is ideal to use with your exsisting add-ons, HATs or pHATs.
Compatible with Windows, Mac & Linux
Powered over USB
Ideal for learning about electronics using real-world inputs & outputs.
Use it to control LEDs, Add a LCD display to your computer, control a robot or more! (Example projects require other components to create.)

AB Electronics IO Pi Plus

Stack up to 4 IO Pi boards on a single Raspberry Pi
32 Digital Inputs/Outputs
External 5V Input with isolation solder jumper
Solder jumper selectable I2C addresses
Configurable interrupt output pins - Configurable as active-high, active-low or open-drain

Pi Supply Mini Modular Breadboard Kit

Modular clip function - rapidly snap and unsnap boards and circuits as your project grows
170 tie points arranged in 34 rows of 5 pins.
Weight: 38.9g
3.5cm x 4.5cm
Self-adhesive backing.

AB Electronics Serial Pi Zero

RS232 Master Port.
Control the Raspberry Pi Zero over RS232 or connect to external serial accessories.
Stackable with other Raspberry Pi accessory boards.
Mounting holes for use with the AB Electronics UK mounting kits (sold separately)

Proto-Pic micro:pixel Edge for micro:bit

10 super high density WS2812B (NeoPixel) LEDs
Plug your micro:bit into the connector, upload your code using the neopixel library and you're good to go!
Microbit is NOT Included

Pi Supply Gert VGA 666 Kit - Hardware VGA for Raspberry Pi

Useful solution for using a VGA screen/monitor with your Raspberry Pi
Capable of displaying 1080p60 VGA video with no CPU load.
The VGA connection is driven natively in hardware over the GPIO pins
It is possible to drive this interface at the same time as the HDMI connection, so a dual screen setup is possible.

AB Electronics RS485 Pi

Use the Raspberry Pi to control external RS-485 devices.
Stackable with other Raspberry Pi accessory boards.
RS-485 Half Duplex Port.
Up to 250 kbps transfer rate.
Mounting holes for use with the AB Electronics UK mounting kits (sold separately)

Proto-Pic micro:pixel 4x8 WS2812B Board for BBC micro:bit

The micro:pixel board also has the micro:bits pins 0, 1 and 2 broken out along with 3v and ground which can accommodate a banana plug or croc clip.
Fully assembled with an edge connector
The micro:pixel uses Pin0 as the LED data pin

Pi Supply PaPiRus Display Extension

PCB Dimensions: 3.4cm x 1.8cm x 0.4cm
Width: 2cm
Length: 20cm
This nifty kit allows you to break out the eInk/ePaper display from the PaPiRus boards.

RasPiO Duino Low Cost Easy Way into Arduino Programming on the Raspberry Pi

Small plug-on board for Raspberry Pi
All the ports are clearly labelled and there are lots of options.
Each of the useful pins on the ATMega are broken out to a cluster of three holes
72 point prototyping area, with GND, 3V3 and 5V rails, where you can add your own components.
Male and female headers are provided, so you can connect whatever you like to your RasPiO Duino.

RasPiO InsPiRing - Programmable RGB LED shapes - Triangle + driver

Each shape has at least one set of inputs and outputs so they can be daisy-chained together.
All the boards are based on 1cm LED spacing and 10cm side
Controllable by Virtually any Platform
Programmable RGB LED boards which can connect together to make whatever 2D or 3D shape you want.

AB Electronics IO Pi Zero

Configurable interrupt source - Interrupt-on-change from configured register defaults or pin changes
Control via the Raspberry Pi I2C port
INTA and INTB can be configured to operate independently or together
Polarity Inversion register to configure the polarity of the input port data
Configurable interrupt output pins - Configurable as active-high, active-low or open-drain
Set Descending Direction

Items 1-20 of 22

Page

Breakout Boards