Cases

Set Descending Direction

Items 1-20 of 28

Page
Material: ABS
Compatible with the Raspberry Pi Model 3B+/3/2
The small fan that's included and is optional to install
Need extra cooling for your Raspberry Pi? This case combined with a cooling fan is for you
This case is compatible with the Raspberry Pi Model 3B+/3/2
Full access to SD Card, USB, Ethernet, Power adapter, and HDMI connector without opening the case
Dimensions: 120 mm x 100 mm x 37 mm
Colour: Grey
Inspired by SNES/NESPi Design
Large cooling fan installed with 2 pin GPIO connector
Simplest Raspberry Pi case assembly on the market
Material: Aluminium
Supplied with a thermal pad and 4 screws
Rubber feet
Built-in heat sink
Easy access to the SD Card and all other ports. You do not need to open the case.
NES Case that is specifically designed for Raspberry Pi 3B+/3B/2B
Functional POWER and RESET buttons
Air ventilation can be installed inside the upper enclosure
Functional LED power indicator
Dimensions: 9.3cm x 4.3cm x 6.3cm
Designed and made in the UK from high-quality material
Access to buttons and LEDs on the PiJuice HAT
Leaves Raspberry Pi status LEDs visible
Cable exits for camera module and optional knock-out parts for extra cable exits if you need them
Access to micro SD port
Comes with a 40 pin GPIO stacking header
4 x rubber feet included
Designed and made in the UK from high quality material
No tools are needed for assembly or disassembly
Access to micro SD port
4 x rubber feet included
Designed and made in the UK from high quality material
No tools are needed for assembly or disassembly
Compatible with the Pi Zero
4 x rubber feet included
Designed and made in the UK from high quality material
No tools are needed for assembly or disassembly
Gap for camera cable
Raspberry Pi Zero clips in. No screws are needed.
Access to micro SD port
Comes with a 40 pin GPIO stacking header
4 x rubber feet included
Designed and made in the UK from high quality material
No tools are needed for assembly or disassembly
Material: ABS & PC-ABS
Raspberry Pi Embossed Lid
Dimensions: 63.9mm x 93.5mm x 26.6mm
Includes 4 x Rubber Feet
3 Part Clip Case
Dimensions: 7.5cm x 6cm x 4.5cm
Designed and made in the UK from high-quality material
Access to buttons and LEDs on the PiJuice HAT
Leaves Raspberry Pi status LEDs visible
Cable exits for camera module and optional knock-out parts for extra cable exits if you need them
4 x rubber feet included
Designed and made in the UK from high quality material
No tools are needed for assembly or disassembly
Leaves all ports accessible
Smooth red finish
Access to micro SD port
4 x rubber feet included
Designed and made in the UK from high quality material
No tools are needed for assembly or disassembly
Compatible with the Raspberry Pi 3, 2, and B+
Access to micro SD port
4 x rubber feet included
Designed and made in the UK from high quality material
No tools are needed for assembly or disassembly
Compatible with the Raspberry Pi 3, 2, and B+
4 x rubber feet included
Designed and made in the UK from high quality material
No tools are needed for assembly or disassembly
Leaves all ports accessible
Smooth black finish that blends in with any audio setup
Access to micro SD port
4 x rubber feet included
Designed and made in the UK from high quality material
No tools are needed for assembly or disassembly
Compatible with the Pi Zero
Comes with 4 x rubber feet
A clear transparent top allows you to keep an eye on your ePaper project
Available with/without a watch strap in black or white
All ports on the PaPiRus HAT and Pi Zero are accessible
5 openings in the case allow you to use the programmable buttons on the PaPiRus Zero pHAT by pressing them with a pen or pencil or similar, without the need to open up the case.
Access to micro SD port
4 x rubber feet included
Designed and made in the UK from high quality material
No tools are needed for assembly or disassembly
Compatible with the Pi Zero
Set Descending Direction

Items 1-20 of 28

Page