HATs & pHATs

Set Descending Direction

20 Items

Designed by Ryanteck LTD
Compatible with Windows 7, 8 & 10. OSX 10.11, macOS 10.12, Ubuntu 16.04, Raspbian & other major linux distributions.
Compatible with most Raspberry Pi add-ons that use GPIO, this device is ideal to use with your exsisting add-ons, HATs or pHATs.
Use it to control LEDs, Add a LCD display to your computer, control a robot or more! (Example projects require other components to create.)
Ideal for learning about electronics using real-world inputs & outputs.
Programming the board to drive a motor is as simple as turning a pin on or off.
Budget friendly motor controller
This now pre-soldered and features a new and improved design breaking out the GPIO Pins to the side of the board.
HAT form factor means that it is more compact to other solutions on the market
Suitable for low power wireless sensor network applications such as irrigation systems, smart metering, smart cities, home automation etc.
Real time monitoring
Fully soldered and assembled. Plug onto your Raspberry Pi, install our software and you’re ready to go! No waiting for compiling.
Low power consumption
Communicates with the Raspberry Pi over UART only using a total of 3 GPIO Pins for the module.
Low power - uses less than 50mA During transmission
Uses RAK811 LoRa Radio with full LoRaWAN Stack embedded
u.FL connector and antenna allowing different antennas to be used or integrated into boxes with external antennas.
Supports LoRaWAN Connections and LoRaP2P Modes.
16-channel, 12-bit PWM controller for the Raspberry Pi
Output frequency is programmable from a typical 40Hz to 1000Hz
The PCA9685 contains 5 I2C address selection pins
Real time Clock (RTC) with CR2032 battery holder.
2 channel 12 bit resolution digital to analogue output (DAC)
8 channel 12 bit resolution analogue input (ADC)
16 channel digital input / outputs
ePaper is a display technology that mimics the appearance of ink on paper.
ePaper reflects light just like ordinary paper and is capable of holding text and images indefinitely, even without electricity.
All signals are broken out to a 40 pin female header.
The display included in this offering is a 1.44" diagonal and 128 x 96 resolution true ePaper / eInk graphical display.
The display does not require any power to keep the image
ePaper is a display technology that mimics the appearance of ink on paper.
Reflects light just like ordinary paper and is capable of holding text and images indefinitely, even without electricity.
All signals are broken out to a 40 pin female header.
The display included in this offering is a 1.44" diagonal and 128 x 96 resolution true ePaper / eInk graphical display.
Daylight readable and is very high contrast.
Polarity Inversion register to configure the polarity of the input port data
Configurable interrupt source - Interrupt-on-change from configured register defaults or pin changes
INTA and INTB can be configured to operate independently or together
Configurable interrupt output pins - Configurable as active-high, active-low or open-drain
Based on the MCP23017 from Microchip Technologies Inc
Power over ethernet add-on board for the Raspberry Pi
Brings the Pi Supply Switch technology together with PoE all in one fantastic package
Power your Raspberry Pi and provide an Ethernet connection in any location with just a single cable.
Perfect for removing the clutter of wires and for reliable use in remote locations.
Plug-and-Play Compatibility with Raspberry Pi 3 Model B+
Integrated Fan Control and 25mm x 25mm Brushless Fan
Output Current: Up to 2.5A
Output Voltage: 5V
Input Voltage: 36V - 56V
Small plug-on board for Raspberry Pi
Once programmed, it can be removed from the Pi and used on its own
72 point prototyping area, with GND, 3V3 and 5V rails, where you can add your own components.
All the ports are clearly labelled and there are lots of options.
Each of the useful pins on the ATMega are broken out to a cluster of three holes
Full driver support in Raspbian / NOOBS
Optional IR receiver included in package
Mounting hardware included
Compatible with Raspberry Pi Zero and the new Pi Zero Wireless
Powered by the Raspberry Pi GPIO header
Mounting holes for use with the AB Electronics UK mounting kits (sold separately)
Stackable with other Raspberry Pi accessory boards.
Use the Raspberry Pi to control external RS-485 devices.
Up to 250 kbps transfer rate.
RS-485 Half Duplex Port.
JustBoom Player pre-configured software available on SD cards from various vendors
Compatible with JustBoom Player / OSMC / RuneAudio / Volumio / Moode / PiCorePlayer / PiMusicBox / OpenELEC and others
Full driver support in Raspbian / NOOBS
Fully HAT compliant
All Raspberry Pi GPIO pins still accessible via 40pin unpopulated extension header
2C address selection via solder jumpers.
External 5V power input for 1-Wire® interface.
Buffered 5V I2C port.
Stackable with other Raspberry Pi accessory boards.
1-Wire® to I2C host interface with ESD protection diode.
Low cost.
A good project to learn to solder with.
Many GND and 5V pins - you need those a lot.
Includes female headers that you can insert jumpers into.
Well labelled pins: They are grouped together logically including - GPIO / I2C / SPI / UART / Power.
Mounting holes for use with the AB Electronics UK mounting kits (sold separately)
Stackable with other Raspberry Pi accessory boards.
Control the Raspberry Pi over RS232 or connect to external serial accessories.
RS232 Master Port.
1-Wire® to I2C host interface with ESD protection diode
Stackable with other Raspberry Pi accessory boards
Buffered 5V I2C port
External 5V power input for 1-Wire® interface
I2C address selection via solder jumpers
Protects the Pi's ports in case you make a wiring error
Arranges the Pi's ports in numerical order to make tinkering easier
Works "out of the box" with GPIO Zero - the new easy-to-use
Python library included in Raspbian
Requires no soldering or assembly
Set Descending Direction

20 Items