Find similar products here

10A Fused Snap In IEC Chassis Plug with Switch

Price match guranteePrice match guarantee

We can price match this item if found elsewhere. Call us on:

0333 400 9500

Quoting product code: N94CZ


About this product


  • Chassis-mounting mains power inlet connector with a built-in fuse holder
  • Accepts a 5 x 20mm cartridge fuse
  • Designed to stop the fuse being removed unless the mains cable is removed first

Product overview

• Chassis-mounting mains power inlet connector with a built-in fuse holder• Accepts a 5 x 20mm cartridge fuse• Designed to stop the fuse being removed unless the mains cable is removed first• Integral on/off switch for ease of use• Nylon housing• Rated at 10A, AC 250 V

Please note: Fuse is not included - Use only with a 250 V fuse.

Rated 1 out of 5 by from I used this for a project, it probably had the mains cable inserted 4 times a month over the last 6 months. In total, about 24 times of plugging in and out the IEC cable. And wouldn't you know it, it broke internally. The fuse is fine, the switch is fine, but the pins have cracked inside. Also, it does not come with a fuse. Small point to note.
Date published: 2014-11-18
Rated 3 out of 5 by from Frustration I bought this item in store where there were no details about what was and wasn't included. I fitted this chassis after carefully cutting a hole. Soldered up and... nothing. Thinking the switch was faulty I de-soldered and remove the chassis from the box, only to find an empty fuse drawer. Visited the website and noticed the description mentions the need for a 5 x 20mm cartridge fuse, which I can't find on the maplin website. After all that fiddling and pushing and pulling and applying heat to the connectors I really hope the unit hasn't been damaged.
Date published: 2015-05-29
Rated 2 out of 5 by from I bought this, cut a hole in the panel, carefully wired and fitted it, switched on and - nothing! I was about to buy an alternative when I read the above 1* review, checked the unit and found no fuse. It works now but the description should really say "(fuse not included, see product code xxx".
Date published: 2014-11-18
  • y_2018, m_2, d_21, h_23
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.7
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_3
  • loc_en_GB, sid_N94CZ, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_maplin-en_gb

Can someone please link me to a spade connector that will fit this item? Thanks 

Asked by: Jon hall
On this occasion Maplin do not stock a product that exactly meets your requirements, or indeed anything close enough to offer you as an alternative.
Answered by: Russell
Date published: 2017-07-21

what are the dimensions of the switch W x H x D

Asked by: robobob
50 mm wide 30.5 mm high 31.9 mm deep (at the deepest point) The exact dimensions of all aspects of the switch are present on the datasheet we have included for your convenience under the downloads tab.
Answered by: Les
Date published: 2017-06-08 Will these fit? Thanks

Asked by: Jon hall
No these would not fit.
Answered by: Billy
Date published: 2017-03-12

Is the rear of this shrouded/ protected from touch e.g. IP2x ?

Asked by: baj25
There is a plastic housing covering all but the 3 connecting points.
Answered by: Gareth
Date published: 2016-06-01

Is there an insulating boot for this product?

Asked by: rob29
In order to fully answer your query we will need to physically examine the item. We have ordered one in to the office and will update this response as soon as we have the required information.
Answered by: Darren
Date published: 2017-08-28

The description states a 5 x 20mm cartridge fuse is required. When I search for a cartridge fuse I get no results. Could you please advise what type of fuse I need for this item?

Asked by: makeurmark
The fuses you need are linked below:
Answered by: Russell
Date published: 2015-07-17

where can i obtain datasheets etc for this item
Asked by: kevin duke
Datasheets can be obtained by contacting our technical team via email. Their direct contact details can be found via the contact us section of the website.
Answered by: DM
Date published: 2015-07-17

dimensions of chassis hole required
Asked by: setnj
47.5mm x 28mm
Answered by: PW
Date published: 2015-07-17
  • y_2018, m_2, d_21, h_23CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.7
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_10
  • loc_en_GB, sid_N94CZ, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_maplin-en_gb