Find similar products here

SPST Illuminated Toggle Switch Red

Price match guranteePrice match guarantee

We can price match this item if found elsewhere. Call us on:

0333 400 9500

Quoting product code: N29BJ

£2.99

Delivery Options

Same day with

Prices Vary

Next day delivery Order online by 6pm

£ 5.99

Named day or time delivery

from £ 8.99

Free Standard delivery 3-5 days (on orders over £10)

Free

Standard delivery 3-5 days (on orders under £10)

£ 2.99

See full details of delivery Options

About this product

Overview

Product overview

• SPST toggle switch where the toggle is illuminated when in the ‘on’ position• Rated 20A @ DC 12 V

Specification

Specifications:
Switch rating: 20A, DC 12 V
Contact rating: 50mΩ maximum
Insulation: DC 500 V, 100MΩ minimum
Dielectric strength: AC 1500 V for 1 minute
Circuit: 3P SPST OFF-ON(LED)
Body size: 24.4 x 14 x 14mm
Bush length: M12 x 11mm long
Dolly: 25mm x 10mm

I have been given 3 numbers for illuminated switches they are N29BJ / N30BJ / N31BJ.  Does each switch have a different colour on the toggle? They are shown as all the same colour on your website

Asked by: Rob Austin
This picture is the same for all models, but the different codes will have different colours, the colour is covered in the title for example this one is the Red one.
Answered by: Russell
Date published: 2017-10-14

LEDs light from about +5V upwards, at that voltage Red, blue and amber are usable, green very feeble. Blue LED is always a lot brighter than others. Each LED draws about 12ma. LEDs only on when switch is flipped. Very pretty used in combination.
Asked by: Alan T
Many thanks for the feedback, the LEDs have a built in resistor tailored for the 12V use, which explains the lack of light at 5V.
Answered by: JK
Date published: 2015-07-17

will this switch work on a motorbike to switch lights on and off
Asked by: wayne
Providing the lights do not draw more than 20A.
Answered by: TJ
Date published: 2015-07-17

Does the switch work at 9v or 5v or does it only opertate at 12v.
Asked by: John
The switch will operate at a lower voltage but the illumination requirers 12v.
Answered by: GM
Date published: 2015-07-17

Connecting the ''Power'' tag to +12V and the ''VCC'' to the load does not let the LED light up when the switch is ON (although the load does operate). Does the ''Ground'' tag need to be earthed for the LED to work?
Asked by: Richard M
Yes the ground does need to be connected.
Answered by: JK
Date published: 2015-07-17

what size mounting hole does this switch require? can it switch mains? or is it limited to 12v? is the 12v for the light?
Asked by: Mark
panel cut out is 12mm. the switch is rated @ 12V 20A so if you wanted to put more voltage through it the amount of current it will handle will decrease.
Answered by: SG
Date published: 2015-07-17

What current does the led use? If used for switching voltages greater than 12V what happens to the illumination?
Asked by: Ralph Stamper
the illumination only works at 12V. Putting a higher voltage through may not work either as the switch contacts are rated 12V also
Answered by: SG
Date published: 2015-07-17

I want to use this switch as a break in an amp remote cable, so that i can toggle a sub woofer on an off, as i dont want to drain my battery, will this work?
Asked by: Jonesy
Yes the product does support that.
Answered by: JK
Date published: 2015-07-17
  • y_2017, m_10, d_21, h_19CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_8
  • loc_en_GB, sid_N29BJ, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_maplin-en_gb

Downloads